Loading...
News Article

Eta Research announces GaN wafers for laser diode makers

News

Eta Research has announced free-standing GaN wafers for laser diode manufacturers at sizes of 2 inches and 4 inches, with conductivity available in either Si-doped n-type or C-doped semi-insulating.

Eta says its GaN wafers have been engineered to meet the requirements for laser diode manufacturers in a number of ways.


Orientation flat alignment

The wafer orientation flat must be closely aligned to the GaN m-plane since lasers may be manufactured by cleaving on the crystallographic plane. Eta has developed the process to achieve 0.0 ± 0.1 degrees alignment of the orientation flat to the crystallographic plane.

Dislocation density

Typical XRD rocking curve FWHM for both (002) and (102) are in the range of 40 to 50 arcsec. The dislocation density was measured by both CL and etch pit methods, and was found to be in the range of 5E5 to 9E5 /cm2.

Offcut

Eta’s standard offcut is 0.5 degrees toward the m-direction and 0.0 inches toward the a-direction at the center point of the wafer. The center point offcut can be customized in the range of 0.2 degrees to 0.6 degrees.

Lattice radius and offcut variation

The lattice radius specification is > 10 m, and typical values range from 20 m to 60 m with the shape as concave. The offcut variation can be calculated from the lattice radius. However, since there is a small concave wafer bow, the actual offcut variation is less than would be calculated from the lattice radius. The offcut was measure by XRD with x-ray reflection alignment to the real wafer surface. The offcut variation over a 4 inches wafer was measured as 0.06 degrees for both the m-direction offcut and a-direction offcut. For example, the m-direction offcut was 0.47 degrees on one edge and 0.53 degrees on the other edge over the entire 100 mm of the wafer.

Frontside Ga-face polish

The Ga-face is polished to an average roughness of 0.15 nm measured by a 10 µm x 10 µm AFM scan. The wafer is cleaned in a special process to remove any contamination from the polishing procedure. Removal of trace metal impurities from the surface was confirmed by TXRF.

Backside N-face finish

The backside finish is available in either polished or etched. The average roughness of the backside surface measured by 3D profiler over 239 µm x 318 µm is 1 nm for polished and 1 µm for etched.

SiC MOSFETs: Understanding the benefits of plasma nitridation
Wolfspeed reports Q2 results
VueReal secures $40.5m to scale MicroSolid printing
Mitsubishi joins Horizon Europe's FLAGCHIP project
Vishay launches new high voltage SiC diodes
UK team leads diamond-FET breakthrough
GaN adoption at tipping point, says Infineon
BluGlass files tuneable GaN laser patents
QD company Quantum Science expands into new facility
Innoscience files lawsuit against Infineon
Riber revenues up 5% to €41.2m
Forvia Hella to use CoolSiC for next generation charging
Photon Design to exhibit QD simulation tool
Ortel transfers CW laser fabrication to Canada
Luminus adds red and blue multi-mode Lasers
PseudolithIC raises $6M for heterogeneous chiplet tech
Mesa sidewall design improves HV DUV LEDs
IQE revenue to exceed expectations
'Game-changing' VCSEL system targets clinical imaging
German start-up secures finance for SiC processing tech
Macom signs preliminaries for CHIPS Act funding
IQE and Quintessent partner on QD lasers for AI
EU funds perovskite tandems for fuel-free space propulsion
EU to invest €3m in GeSi quantum project
Transforming the current density of AlN Schottky barrier diodes
Turbocharging the GaN MOSFET with a HfO₂ gate
Wolfspeed launches Gen 4 SiC MOSFET technology
Report predicts high growth for UK's North East
Element Six unveils Cu-diamond composite
SemiQ launches hi-rel 1700V SiC MOSFETs
Lynred to exhibit Eyesential SWIR sensor for machine vision
Thorlabs buys VCSEL firm Praevium Research
×
Search the news archive

To close this popup you can press escape or click the close icon.
Logo
x
Logo
×
Register - Step 1

You may choose to subscribe to the Compound Semiconductor Magazine, the Compound Semiconductor Newsletter, or both. You may also request additional information if required, before submitting your application.


Please subscribe me to:

 

You chose the industry type of "Other"

Please enter the industry that you work in:
Please enter the industry that you work in: