Loading...
News Article

Researchers improve CdTe cell voltage

Open-circuit voltage breaks the 1V barrier for the first time


A US team has improved the maximum voltage available from a CdTe solar cell, overcoming a practical limit that has been pursued for 60 years and is said to be key to improving efficiency.

The research was led by the US Department of Energy's National Renewable Energy Laboratory and in collaboration with Washington State University and the University of Tennessee. 

Silicon solar cells represent 90 percent of the solar cell market, but it will be difficult to significantly reduce their manufacturing costs. CdTe solar cells offer a low-cost alternative. They have the lowest carbon footprint of any other solar technology and perform better than silicon in real world conditions, including in hot, humid weather and under low light. However, until recently, CdTe cells haven't been as efficient as silicon-based cells.

One key area where CdTe has underperformed was in the maximum voltage available from the solar cell, called open-circuit voltage. Limited by the quality of CdTe materials, researchers have not been able to get more than 900mV out of the material, which was considered its practical limit.

The research team improved cell voltage by shifting away from a standard processing step using cadmium chloride. Instead, they placed a small number of phosphorus atoms on tellurium lattice sites and then carefully formed ideal interfaces between materials with different atomic spacing to complete the solar cell.

This approach improved the CdTe conductivity and carrier lifetime each by orders of magnitude, thereby enabling the fabrication of CdTe solar cells with an open-circuit voltage breaking the 1V barrier for the first time. 

"It's a significant milestone. It's been below 900 millivolts for decades," said Kelvin Lynn (pictured above), Regents professor in WSU's School of Mechanical and Materials Engineering and Department of Physics, who led WSU's effort.

The NREL researchers treated the crystals, built and characterised the solar cells, while WSU researchers developed  the crystal material used in the cells.

The WSU researchers grow their crystals in a technique called melt growth, which allows precise control over purity and composition. Purity is extremely critical to the process, so the researchers mix, prepare and vacuum-seal the materials in an industry-standard clean room. They then synthesise the crystal in a furnace above 1100 degC and then cool it from the bottom up at a rate of about one millimeter per hour. The researchers then cut the crystal into polished wafers to make the solar cells.

"Others have tried dopants, but they didn't have the control and purity that we have. And, the purity matters,'' said Lynn. "WSU is known for growing really high quality and purity crystals. You have to control every step."

While researchers have improved silicon-based cells almost to their theoretical limit, there is significant room for efficiency improvements for CdTe which could be bettered by an additional 30 percent, said Lynn.

'CdTe solar cells with open-circuit voltage breaking the 1 V barrier'  by JM Burst et al;  Nature Energy Article number: 16015 (2016)

SiC patenting strong in Q4 2024, says KnowMade
Say hello to the heterogeneous revolution
Double heterostructure HEMTs for handsets
AlixLabs to collaborate with Linköping University
SiC MOSFETs: Understanding the benefits of plasma nitridation
Wolfspeed reports Q2 results
VueReal secures $40.5m to scale MicroSolid printing
Mitsubishi joins Horizon Europe's FLAGCHIP project
Vishay launches new high voltage SiC diodes
UK team leads diamond-FET breakthrough
GaN adoption at tipping point, says Infineon
BluGlass files tuneable GaN laser patents
QD company Quantum Science expands into new facility
Innoscience files lawsuit against Infineon
Riber revenues up 5% to €41.2m
Forvia Hella to use CoolSiC for next generation charging
Photon Design to exhibit QD simulation tool
Ortel transfers CW laser fabrication to Canada
Luminus adds red and blue multi-mode Lasers
PseudolithIC raises $6M for heterogeneous chiplet tech
Mesa sidewall design improves HV DUV LEDs
IQE revenue to exceed expectations
'Game-changing' VCSEL system targets clinical imaging
German start-up secures finance for SiC processing tech
Macom signs preliminaries for CHIPS Act funding
IQE and Quintessent partner on QD lasers for AI
EU funds perovskite tandems for fuel-free space propulsion
EU to invest €3m in GeSi quantum project
Transforming the current density of AlN Schottky barrier diodes
Turbocharging the GaN MOSFET with a HfO₂ gate
Wolfspeed launches Gen 4 SiC MOSFET technology
Report predicts high growth for UK's North East
×
Search the news archive

To close this popup you can press escape or click the close icon.
Logo
x
Logo
×
Register - Step 1

You may choose to subscribe to the Compound Semiconductor Magazine, the Compound Semiconductor Newsletter, or both. You may also request additional information if required, before submitting your application.


Please subscribe me to:

 

You chose the industry type of "Other"

Please enter the industry that you work in:
Please enter the industry that you work in: