Loading...
News Article

IBM multijunction flower cell aims to hit 2000 suns

The firm's prototype HCPVT system uses a large parabolic dish, incorporating many mirror facets, which are attached to a sun tracking system. The tracking system positions the dish at the best angle to capture the sun's rays, which then reflect off the mirrors onto several microchannel-liquid cooled receivers with triple junction compound semiconductor chips
Scientists are collaborating to increase concentrating solar radiation by 2,000 times and converting 80 percent of the incoming radiation into useful energy.

The system could also provide desalinated water and cool air in sunny, remote locations where they are often in short supply.

A three-year, $2.4 million (2.25 million CHF) grant from the Swiss Commission for Technology and Innovation has been awarded to scientists at IBM Research, Airlight Energy, a supplier of solar power technology, ETH Zurich (Professorship of Renewable Energy Carriers) and the Interstate University of Applied Sciences Buchs NTB (Institute for Micro- and Nanotechnology MNT).

Together, the institutes aim to develop an economical High Concentration PhotoVoltaic Thermal (HCPVT) system.

Based on a study by the European Solar Thermal Electricity Association and Greenpeace International, technically, it would only take two percent of the solar energy from the Sahara Desert to supply the world's electricity needs.

According to this study, the researchers say that solar technologies on the market today are too expensive and slow to produce; they require rare Earth minerals and lack the efficiency to make such massive installations practical.

The prototype HCPVT system uses a large parabolic dish, made from a multitude of mirror facets, which are attached to a sun tracking system. The tracking system positions the dish at the best angle to capture the sun's rays, which then reflect off the mirrors onto several microchannel-liquid cooled receivers with triple junction photovoltaic chips. Each 1x1 centimetre chip can convert 200-250 watts, on average, over a typical eight hour day in a sunny region.

The entire receiver combines hundreds of chips and provides 25 kilowatts of electrical power. The photovoltaic chips are mounted on micro-structured layers that pipe liquid coolants within a few tens of micrometers off the chip to absorb the heat and draw it away 10 times more effective than with passive air cooling.

The coolant maintains the chips almost at the same temperature for a solar concentration of 2,000 times and can keep them at safe temperatures up to a solar concentration of 5,000 times.

The direct cooling solution with very small pumping power is inspired by the hierarchical branched blood supply system of the human body and has been already tested by IBM scientists in high performance computers, including Aquasar.

An initial demonstrator of the multi-chip receiver was developed in a previous collaboration between IBM and the Egypt Nanotechnology Research Centre.

"We plan to use triple-junction photovoltaic cells on a micro-channel cooled module which can directly convert more than 30 percent of collected solar radiation into electrical energy and allow for the efficient recovery of an additional 50 percent waste heat," says Bruno Michel, manager, advanced thermal packaging at IBM Research.

"We believe that we can achieve this with a very practical design that is made of lightweight and high strength concrete, which is used in bridges, and primary optics composed of inexpensive pneumatic mirrors -it's frugal innovation, but builds on decades of experience in microtechnology."

"The design of the system is elegantly simple," adds Andrea Pedretti, chief technology officer at Airlight Energy. "We replace expensive steel and glass with low cost concrete and simple pressurised metalised foils. The small high-tech components, in particular the microchannel coolers and the moulds, can be manufactured in Switzerland with the remaining construction and assembly done in the region of the installation. This leads to a win-win situation where the system is cost competitive and jobs are created in both regions."

The solar concentrating optics will be developed by ETH Zurich. "Advanced ray-tracing numerical techniques will be applied to optimise the design of the optical configuration and reach uniform solar fluxes exceeding 2,000 suns at the surface of the photovoltaic cell," explains Aldo Steinfeld, a professor at ETH Zurich.

With such a high concentration and a radically low cost design scientists believe they can achieve a cost per aperture area below $250 per square meter, which is three times lower than comparable systems. The levelised cost of energy will be less than 10 cents per kilowatt hour (KWh).

For comparison, feed in tariffs for electrical energy in Germany are currently still larger than 25 cents per KWh and production cost at coal power stations are around 5-10 cents per KWh.

Water Desalination and Cool Air

Current concentration photovoltaic systems only collect electrical energy and dissipate the thermal energy to the atmosphere. With the HCPVT packaging approach scientists can both eliminate the overheating problems of solar chips while also repurposing the energy for thermal water desalination and adsorption cooling.



To capture the medium grade heat IBM scientists and engineers are utilising an advanced technology they developed for water-cooled high performance computers, including Aquasar and SuperMUC. With both computers water is used to absorb heat from the processor chips, which is then used to provide space heating for the facilities.

"Microtechnology as known from computer chip manufacturing is crucial to enable such an efficient thermal transfer from the photovoltaic chip over to the cooling liquid," says Andre Bernard, head of the MNT Institute at NTB Buchs. "And by using innovative ways to fabricate these heat transfer devices we aim at a cost-efficient production."

In the HCPVT system, instead of heating a building, the 90 degree Celsius water will be used to heat salty water that then passes through a porous membrane distillation system where it is vaporized and desalinated. Such a system could provide 30-40 litres of drinkable water per square metre of receiver area per day, while still generating electricity with a more than 25 percent yield or two kilowatt hours per day - a little less than half the amount of water the average person needs per day according to the United Nations, but a large installation could provide enough water for a town.

The HCPVT system can also provide air conditioning by means of a thermal driven adsorption chiller. An adsorption chiller is a device that converts heat into cooling via a thermal cycle applied to an absorber made from silica gel, for example.

Adsorption chillers, with water as working fluid, can replace compression chillers, which stress electrical grids in hot climates and contain working fluids that are harmful to the ozone layer.

Scientists envision the HCPVT system providing sustainable energy and potable water to locations around the world including southern Europe, Africa, Arabic peninsula, the southwestern part of the United States, South America, and Australia.

Remote tourism locations are also an interesting market, particularly resorts on small islands, such as the Maldives, Seychelles and Mauritius, since conventional systems require separate units, with consequent loss in efficiency and increased cost.

A prototype of the HCPVT system is currently being tested at IBM Research in Zurich. Additional prototypes will be built in Biasca and Rueschlikon, Switzerland as part of the collaboration.

 

×
Search the news archive

To close this popup you can press escape or click the close icon.
Logo
x
Logo
×
Register - Step 1

You may choose to subscribe to the Compound Semiconductor Magazine, the Compound Semiconductor Newsletter, or both. You may also request additional information if required, before submitting your application.


Please subscribe me to:

 

You chose the industry type of "Other"

Please enter the industry that you work in:
Please enter the industry that you work in: